Quote from: 280Z Turbo on May 24, 2014, 10:14:20 PM
From what I read, Holleys are good for performance, but have shitty fuel economy on the street. Edelbrocks are good for people without the brains to learn how the Rochester works.

The solution

Quote from: FoMoJo on May 25, 2014, 06:49:48 PM
The solution

Yeah, Webers are good for people with deep pockets.

Those unfiltered air horns are good for sucking in engine destroying debris.

Quote from: 280Z Turbo on May 25, 2014, 06:52:24 PM
Yeah, Webers are good for people with deep pockets.

Those unfiltered air horns are good for sucking in engine destroying debris.

You CAN get filters for them you know.

But, my experience with webers on VWs is that they only really work good at full throttle.

A PO stuck helper springs over the rear shocks to help support the rear end of the car. A normal person would have just replaced the worn leaf spring.


The differential rear cover is cracked. This is where the rear spring mounts. It's been broken since at least 1977, so no emergency, I guess.


Carb  pulled apart:


Did the old JB weld over the leaky plugs trick for early Quadrajets.

Got KYB Monotube rear shocks, a new leaf spring, all new bushings, and a stronger rear end cover coming. Also realized one of the wheel cylinders was leaking, so those will be replaced.

Once that's done, the likelihood of death while operating the car will decrease by 50%.

The front suspension has rotted bushings, bad shocks, and a loose rag joint, but I'm less concerned with it.

Quote from: Soup DeVille on May 25, 2014, 07:07:08 PM
You CAN get filters for them you know.

But, my experience with webers on VWs is that they only really work good at full throttle.

We had a 48 IDA on the Mazda. It wasn't bad once it was tuned properly. They're also really cool looking.

Wouldn't start worth a damn in the cold, though.

Anybody ever rebuild a GM steering box?

I'm looking into a rebuild kit for $80.

Is it a Delphi 700 series?

You can get a rebuilt one for just a bit more, I think. Unless you wanna do the work. But I think I paid $80 for a new one from a Monte Carlo that has way less slop and isn't boosted so much. (Compared to a late 60s Chevelle, not sure what the Corvettes are like)

It's manual.

Got the car running, but still need to tune in the timing. The battery ran out of juice as we were cranking it a lot trying to get it set correctly.

I'm thinking the issue is the starter. It was drawing a ton of current and heating up the cables, so I'm thinking it's time to get a remanufactured unit.

This direct drive starter is a monster. I placed a bottle cap on it for scale:


Squeeky clean Quadrajet with rebuilt distributor and new Pertronix coil:

Asked about 16" rims on a Corvette forum. At least 1 post was useful. (sigh)

http://forums.corvetteforum.com/c1-and-c2-corvettes/3480911-pictures-of-c2s-with-16-rims.html#post1587082424

Here's a nice '63 with 16's.

I think they look way better than 17's or 15's.

http://www.ebay.com/itm/1963-CHEVROLET-CORVETTE-ROADSTER-TRIPLE-RED-RESTORED-VETTE-SELLING-NO-RESERVE-/121358256043?_trksid=p2054897.l4275

Quote from: 280Z Turbo on June 07, 2014, 10:59:29 PM
Asked about 16" rims on a Corvette forum. At least 1 post was useful. (sigh)

http://forums.corvetteforum.com/c1-and-c2-corvettes/3480911-pictures-of-c2s-with-16-rims.html#post1587082424

Today I learned that they don't make 16" tires anymore...

Quote from: Soup DeVille on June 07, 2014, 11:49:25 PM
Today I learned that they don't make 16" tires anymore...

Wat?

Quote from: mzziaz on June 08, 2014, 01:42:54 AM
Wat?

Oh, reading the responses at the Corvette forum that was linked, that's all.

Of course they make 16 inch tires still, and will fo rthe forseeable future too.

Oh, you've found some forum "knowledge"!

Quote from: mzziaz on June 08, 2014, 02:02:28 AM
Oh, you've found some forum "knowledge"!

I was especially impressed when the one chap explained that I could find 17 inch wheels if I did a search for "17s"

Unfortunately, stupid google thinks this has something to do with airplanes.

Quote from: Soup DeVille on June 08, 2014, 03:08:57 AM
I was especially impressed when the one chap explained that I could find 17 inch wheels if I did a search for "17s"

Unfortunately, stupid google thinks this has something to do with airplanes.

One of the worst parts of being a mustang owner is having to wade through the Norwegian amcar  forums when I need something.

Its like the political threads here. So many opinions, so few facts.

Quote from: 280Z Turbo on June 07, 2014, 11:19:03 PM
Here's a nice '63 with 16's.

I think they look way better than 17's or 15's.

http://www.ebay.com/itm/1963-CHEVROLET-CORVETTE-ROADSTER-TRIPLE-RED-RESTORED-VETTE-SELLING-NO-RESERVE-/121358256043?_trksid=p2054897.l4275

I like.

Well, they're right in as much as you'll have a harder time finding performance tires of the correct OD with a 16" tire versus a lower profile 17" tire.  I ran into this with the Mustang when I wore out the OEM 17" tires.  The OEM tires had a 60 aspect ratio, and I could only go up another 10mm in width and still fit on the rim, which limited me to no lower than a 55 series tire.  Very little in hi-po summer tires with more than a 50 aspect ratio.  I think there were only 2 or 3 on Tirerack, versus a dozen if I went up to a wider, 18" wheel. 

That said, this isn't a resto-mod and you probably don't care about having really high performance tires.  A modern grand touring tire or sport all season is likely better than what came on those cars from the factory.

And I agree, the 16" wheel seems to be the sweet spot.  Still enough sidewall to look reasonably authentic, but it fills the wheel well a bit better than the 15s.

Quote from: MX793 on June 08, 2014, 06:29:13 AM
Well, they're right in as much as you'll have a harder time finding performance tires of the correct OD with a 16" tire versus a lower profile 17" tire.  I ran into this with the Mustang when I wore out the OEM 17" tires.  The OEM tires had a 60 aspect ratio, and I could only go up another 10mm in width and still fit on the rim, which limited me to no lower than a 55 series tire.  Very little in hi-po summer tires with more than a 50 aspect ratio.  I think there were only 2 or 3 on Tirerack, versus a dozen if I went up to a wider, 18" wheel. 

That said, this isn't a resto-mod and you probably don't care about having really high performance tires.  A modern grand touring tire or sport all season is likely better than what came on those cars from the factory.

And I agree, the 16" wheel seems to be the sweet spot.  Still enough sidewall to look reasonably authentic, but it fills the wheel well a bit better than the 15s.

Likely better? Even Ching-Chong Squeelmaster All Seasons are better than 6.70x15 bias plies.

Got the car started. Runs a lot better now, but still has a weird issue where it won't return to a proper idle after a quick blip of the throttle. It wants to idle low, but give it a little gas and it will return to normal. Could the choke pull off cause this?

Also, it has a weird intermittent popping sound out the exhaust at idle. With the ignition and carburetor sorted, I'm thinking there must be a valve issue. Perhaps the valves are leaking?

Quote from: mzziaz on June 08, 2014, 03:35:58 AM


One of the worst parts of being a mustang owner is having to wade through the Norwegian amcar  forums when I need something.

Its like the political threads here. So many opinions, so few facts.

Yes, yes...poor little European doesn't like our brash American capitalism.

Quote from: 280Z Turbo on June 08, 2014, 04:04:37 PM
Got the car started. Runs a lot better now, but still has a weird issue where it won't return to a proper idle after a quick blip of the throttle. It wants to idle low, but give it a little gas and it will return to normal. Could the choke pull off cause this?

Yes.

Quote from: 280Z Turbo on June 08, 2014, 04:14:48 PM
Yes, yes...poor little European doesn't like our brash American capitalism.

Norwegian amcar forums. I´m sure we have world class boneheads.

Quote from: mzziaz on June 08, 2014, 05:13:33 PM
Norwegian amcar forums. I´m sure we have world class boneheads.

I was referring to us.

Quote from: Soup DeVille on June 08, 2014, 04:33:51 PM
Yes.

I'm going to have my dad pick up a new choke pull off this week. I tested the current one and it leaks.

Thinking about pulling the body off this winter. How hard could it be?

What's gonna be hard is all the sins you're gonna find (and will have to correct now that you see them) .

Quote from: GoCougs on June 09, 2014, 08:19:35 AM
What's gonna be hard is all the sins you're gonna find (and will have to correct now that you see them) .

Unless you have a good reason or want a lot more work, probably best to not open the closet door and see the cobwebs.